Vibralite 3 Watch

VIBRATION WATCH with:

Vibration Alarm won't disturb others.

Beep Alarm option

Auto Reload Countdown Timer can be set for seconds, minutes & hours.

Electro-Luminescent backlight For viewing display at night.

Second Clock great when traveling in a different time zone.

Two Alarm Settings use for daily reminders, wake up, snooze, medication.

 

Hourly Alert/Chime Option: 12 or 24 Hour clock, Stopwatch

 

OPERATING MODES

Your watch has six operating modes:

To go from one operating mode to another, repeat pressing the MODE button for each mode to be displayed. The operating modes will rotate in the order as listed above.

TO BECOME FAMILIAR WITH THE OPERATING MODES &

THEIR SYMBOLS, ROTATE THROUGH EACH MODE BY

PRESSING THE ‘MODE” BUTTON.

 

FIRST TIME SETTING OF YOUR CALENDAR/CLOCK

(You must have this set for your Alarm Settings to be accurate.)

When setting the Calendar & Clock, the rotation for setting is

Seconds, Hour, Minutes, 12/24Hr, Date, Month, Day of Week.

ONLY when the digits are BLINKING can you set or change

the setting. The clock will stop blinking when no button is pressed

for two minutes. You cannot switch to another mode of

operation while the display is blinking. To exit and stop the

blinking, push LAP/RESET button.

1. Repeat pressing the MODE button until the CALENDAR

CLOCK operating mode shows on the display.

2. Press & Hold the LAP/RESET button until the second’s digits

begin to BLINK. Press the START/STOP button to reset the second’s display to 00 00.

3. Press the MODE button. The hour digits will begin to BLINK.

Press the START/STOP button to rotate to correct hour of the day.

WHEN IN THE 12 HR MODE, A PM INDICATOR WILL

APPEAR ON THE DISPLAY ABOVE AND LEFT OF THE

HOUR DIGITS. AS YOU ROTATE TO 12 HOURS THE

PM MUST SHOW FOR SETTING CORRECT TIME

FOR AFTERNOON OR EVENING. BE SURE TO SET

CORRECTLY FOR THE CURRENT TIME OF DAY.

4. Press the MODE button to go to the minute digits. The minute

digits will begin to BLINK. Press the START/STOP button

to rotate to the correct minute.

5. Press the MODE button and the 12H or 24H will show and

BLINK on the display. Press the START/STOP button to change

from 12H to 24H or from 24H to 12H.

6. Press the MODE button for the date of the month. A number

will BLINK at the top left corner of the display. Press the

START/STOP button to rotate to the correct date of the month (1-31)

7. Press the MODE button for the Month. A number will BLINK

on the display. Press the START/STOP button to rotate

to the current month of the year.  (Example; 6 for Jun, 9 for Sept)

8. Press the MODE button for the Day of the Week. A two-letter

abbreviation at the top of the display will BLINK. Press the

START/STOP button to rotate to the correct day. (Example TU

for Tuesday; TH for Thursday)

9. Press the LAP/RESET button when you have finished the

correct set up. The display will stop blinking.

 

HOW TO SET AN ALARM CLOCK (Setting procedure is the same for BOTH alarms)

1. Repeat Pressing the MODE button to rotate to the alarm

operating mode you want: A1 = 1st ALARM or A2 = 2ND ALARM.

2. Press & Hold the LAP/RESET button until the hour digits BLINK.

Press the START/STOP button to rotate to the hour wanted.

Note: In the 12 Hr Mode, remember to use the PM indicator for correct setting.

3. Press the MODE button to go to the minutes. The minutes will

BLINK. Press the START/STOP button to rotate to the minute wanted.

4. Press the LAP/RESET Button when finished. The display will

stop blinking. The set icon will show on the display. Your alarm is set.

When A1 Alarm is set the icon shows beside the PM indicator

under Alm1 Alm1. When A2 Alarm is set the icon shows on the display beside the A1 icon under Alm2 Alm2.

Note: Calendar Clock Time must be set for Alarm Time activation to be correct.

HOW TO TURN ON AND OFF THE HOURLY ALERT

Note: Hourly Alert is a short single reminder

1. Repeat Pressing the MODE button and select either 1st

ALARM=A1 or 2ND ALARM=A2

2. Repeat Pressing START/STOP button until the Hourly Alert

indicator (located beside the Alm2 indicator) shows on the

display. Hourly alert is on when icon shows. Hourly alert is off when icon doesn’t show.

ON/OFF SETTINGS OF ALARMS

Note: To turn on or off First Alarm you must be in the A1 mode.

To turn on or off Second Alarm you must be in the A2 mode.

Repeat Pressing the MODE button to show alarm you wish to turn off or on: 1ST OR 2ND ALARM.  Repeat Pressing the START /STOP button to rotate, alarm on (hourly alert) & alarm off. When Icon(s) shows, alarm is set. Alarm is off when icon does not show. (See previous illustration)

 

HOW TO ACTIVATE OR DEACTIVATE VIBRATION AND BEEP FUNCTION

1. Repeat Pressing the MODE button to the CALENDAR CLOCK mode.

2. Repeat Pressing the START/STOP button to rotate through the selection of settings.

When a function is activated, its respective icon will be highlighted, at the top right corner of the display. Rotation will be: Vibration ON, Beep ON, Vibration and Beep ON, Vibration & Beep OFF. Select one of the four functions that you desire. This can be changed at anytime by following steps 1 and 2.

 

Alarm will stop automatically after approximately 20 seconds. To stop alarm before the automatic stop, press any button. NOTE: To check setting the watch is in at any time, press the MODE button. With each press of the button the vibration and/or beep will respond if set.

 

HOW TO USE THE COUNTDOWN TIMER

1. Repeat Pressing the MODE button to display TR (COUNTDOWN TIMER) operating mode.

2. Press & Hold the LAP/RESET Button until the Seconds digits

BLINK. Press the START/STOP button to set to the seconds wanted. You can select from 0 to 59 seconds. If you do not wish to set the seconds, go to #3 below.

3. Press the MODE Button to go to the hours. The hour digits will

BLINK. Press the START/STOP button to set the number of hours wanted. You can select from 0 to 23 hours.

4. Press the MODE Button to go to the minutes. The minute digits

will BLINK. Press the START/STOP button to set the number of minutes wanted. You can select from 0 to 59 minutes.

5. Press LAP/RESET button when you have finished. The display

will stop blinking. To reset the Countdown Timer for a different time see "How to Use the Countdown Timer" and follow instructions.

 

TO START THE COUNTDOWN TIMER,

Press the START/STOP button (after the countdown timer is set).

The timer will start to countdown. To interrupt, press the START/STOP button. Pressing the START/STOP button again will start the countdown from where it last left off.

 

Note: When Countdown Timer is set for more than ten minutes, a

short single reminder will advise you of 10 minutes remaining and

then at 5 minutes remaining.

 

AUTO RELOAD COUNTDOWN TIMER will automatically reload for the time preset, when the timer reaches “0”

 

If you do not wish to start the countdown again immediately,

press the START/ STOP button twice, if alarm is activated. Press

once to stop the countdown if alarm is not activated.

 

To restart the preset countdown at any time, press the START/STOP button while in the COUNTDOWN - TR mode.

 

TO USE THE REPEATABLE COUNTDOWN TIMER WITH PAUSES IN BETWEEN When the auto-repeat countdown timer reaches zero it automatically alarms and starts to countdown again for the preset time. You can cancel the countdown before it reaches zero and return to the original countdown time as needed.

 

You must be in the Countdown Timer Mode to reset to the original

countdown time. PUSH the LAP/RESET button and HOLD IT for approximately 2 to 3 seconds. Digits will flash showing the amount of time that the countdown was set for originally. Push the LAP/RESET button once, and the digits will stop flashing. (If you do not push the LAP/RESET button to stop the flashing, the digits will stop flashing automatically after 2 minutes.) To activate the start of the countdown when you need it, push the START/STOP button once.

 

HOW TO USE THE STOPWATCH

1. Repeat Pressing the MODE button to show STOPWATCH

on the display.

2. To start the Stopwatch press the START/STOP button. The

Stopwatch will start keeping time and the Icon (symbol at the

top of the display) will flicker to show the action.

 

TO STOP THE STOPWATCH, press the START/STOP button.

Pressing the START/STOP button again will start the stopwatch

running from where it last left off. The Stopwatch can count up to 23 hours, 59 minutes and 59 59.99 99 seconds. Each hour accumulated shows at the top left of the display.

 

To RESET the stopwatch to zeros, press the LAP/RESET button,

when it is in a stop position. Split Timing on Stopwatch 1. Start the Stopwatch by pressing the START/STOP button. The stopwatch will start keeping time.

2. Press the LAP/RESET button. The watch will continue

counting the time even though you do not see it on the display.

The Icon at the top of the display will continue to flicker

to show action and that counting continues.

3. Press the LAP/RESET button again and the display will

change and show the time that has accumulated in total.

 

To RESET the Stopwatch, press the START/STOP button and then press the LAP/RESET button.

 

HOW TO SET THE SECOND CLOCK

1. Repeat Pressing the MODE button to show SECOND CLOCK (T2)

2. Press & Hold the LAP/RESET button until the Hours digits BLINK.

Press the START/STOP button to rotate to the hour you wish to

set. (In 12 Hr Mode, use PM indicator for correct setting of

afternoon or evening.)

3. Press the LAP/RESET button when desired hour has been set.

NOTE: Only the hour can be set in second clock mode. (The minutes and seconds will be the same as the Calendar Clock)

 

HOW TO USE THE EL BACK LIGHT

Press the LIGHT button to light up the LCD display at any time. The screen will be lit for approximately 3 seconds before going off

automatically. The EL back light will flash when an alarm is activated

 

BATTERY INFORMATION

Your watch uses a Standard 3 volt lithium CR2032 or equivalent

battery. Battery life will vary due to how often the EL back light and

vibration function are used. To maintain water resistance, a

qualified person should replace the battery

 

DISCLAIMER

GLOBAL does not accept any responsibility what so ever for any

inconvenience or non-compliance for medication or any other

reminder the watch may be used for.

 

VibraLITE watches are not intended to be worn during

swimming, diving, or showering.

 

SERVICE

Qualified service personnel should service this unit. The user should not attempt to service the unit.

 

Servicing should be referred to:

Global Assistive Devices, Inc.

4950 North Dixie Highway,

Fort Lauderdale FL USA 33334

Before sending your unit for service, have the battery checked

and/or try resetting by pressing all four buttons at the same time and hold until the display clears.

 

ONE YEAR LIMITED WARRANTY

Your VibraLITE 3 is warranted to be free from defects in material or workmanship for One Year from the date of purchase.

This is a limited warranty and covers watch functions only. This

warranty does not apply to the battery, band or to any unit which

has been subject to misuse, negligence or accident. This

warranty is void if the watch has been tampered with, altered, or

repaired other than by a qualified service center. At its option,

 

GLOBAL ASSISTIVE DEVICES, INC.

may select to replace the unit, rather than repair it. During the

warranty period, return the watch, with dated proof of purchase, in a secure package, insured and with shipping charges prepaid. No

C.O.D. packages will be accepted.  Please include a note describing  the service required and include $10.00 (check, money order, Visa, MasterCard, American Express, or Discover) for shipping and handling in the USA. Other Countries please contact us for pricing.

 

OUT OF WARRANTY SERVICE

Follow the same procedure for shipping to us as you would for

warranty service. Be sure to include a description of the

problem. An estimate will be submitted for your approval for

any labor or parts not covered by the warranty before any work is

performed.

 

Copyright:

GLOBAL ASSISTIVE DEVICES, INC.

Fort Lauderdale FL 33334 USA